~Chainmaille Jewelry~

These are what have been some of my better (and older, I have more to add someday) selling designs in the past, and ones that I will likely make more of. Though they are not shown very much here, I have also done a lot of bracelets and necklaces from the standard chain weaves (Persian, Half-Persians, Byzentine, Boxchain, etc.) For more about those, check out my page of maille weaves, or my page of instock items for more pictures of my chainmaille jewelry work and some additional information on it.

Roller Chain Collar/Gorget/Choker

Coin Wrap Pendants
The original of this item, shown to the left, was made as a holiday gift for a friend. I liked the pentacle design on one side and wanted to turn the coin into a pendant, without drilling a hole in it. After many hours of thought, the idea came to me that I should somehow frame the coin in maille. I worked all night on designs and it wasn't until about ten o'clock the next morning that I had something done that I was satisfied with. The maille holds the coin tightly in place and there is no danger of the coin falling out. I have been wearing one I made for myself since December '01 and the coin shows no signs of coming loose from the wrap. The maille is made from Stainless Steel. The coin in the one to the left is a coin from The Empire Cherifien, now known as Morocco. Because of the nature of maille and round metal rings, designs for wraps for different sized coins may vary slightly. As shown in the picture, one side of coin is covered by maille, and the other is left exposed. Click HERE for a picture of another coin wrap and examples of other coins I am planning to wrap, or have already wrapped since typing this.

Choker/Necklace with Dags
Made with 1/8" inner diameter 20 gauge
Stainless Steel rings. Comes with my
standard hook clasp but other clasp
types may be available if desired.

ID Fade Mantle/Necklace
This is short mantle/necklace is made from different size
rings alowing it to expand without using the expanding/idle
ring methods. Its made from 18 gauge Stainless Steel rings.
I've also made these in blued stainless and blued Mild Steel.

Diamond Pattern Choker/Mantle
A Similar design to the "Diamond Pattern Choker"
listed further down on this page, this one is
made to be worn lower on the neck and spread out
over the shoulders a bit. Made with 20 gauge
Stainless Steel, 1/8"ID links.

European/Japanese weave Choker
This is made with one of my own weaves that's a mix of European and oriental weaves and uses two ring sizes. There are three versions of this choker available... the one in the picture is what I call two-strand because it is made from two chains connected together. One-strand and Three-strand versions are also available. Ring sizes used in this choker are 1/4" ID 16 guage rings and 1/8" ID 20 gauge rings, both made from stainless steel.
One-strand ...$30...
Two-strand ...$40...
Three-strand ...$50...

Cylinder Chain Bracelet
A smooth feeling, ropelike bracelet.
The rings have an inner diameter of 1/8"
and are made from 20 guage Stainless Steel.

X-Wide Boxchain Bracelet
This Bracelet is made from two lengths of small
link stainless steel boxchain connected together
at a corner. Made with 5/32" inner diameter rings
of 20 gauge stainless steel.

Chainmaile Ring #1
This Stainless Steel ring of maile is made from
20 gauge 1/8" inner diameter rings. These are
very size specific and are best when they fit a
little tight so they do not slip off.

Chainmaile Ring #2
A Stainless Steel ring made from the basic element
of the oriental weaves, a simple chain of large and
small rings. The large rings are 1/4 inch inner
diameter 16 gauge, the small ones are 1/8 inch ID
18 gauge.

Cylinder chain w/ fringe Ear Rings
It's a small Cylinder Chain with
three short strips of King's Maile
hanging from the bottom of it.
Made with 20 Guage Stainless Steel
rings with an inner diameter of 1/8".
They are about two inches long.